Brief Introduction

FS-V33P

ModelFS-V33CPType2-output withM8 connectorOutputPNPMain unit/Expansion unitMain unitControl output2 outputsMonitor output (1 to 5 V)N/AExternal inputConnectorM8Light source LEDRed, 4-element LED (Wavelength: 640 nm)Response time33 µs (HIGH SPEED) /250 µs (FINE) /500 µs (TURBO) /1 ms (SUPER TURBO) /4 ms (ULTRA TURBO) /16 ms (MEGA TURBO)Output selectionLIGHT-ON/DARK-ON (switch-selectable)Display indicatorOperation indicator: Red LED/Dual digital monitor: Dual 7-segment display, Preset Value (4-digit green LED indicator) andCurrent Value (4-digit red LED indicator) illuminated together. Current Value range: 0 to 64,512; Excess gain: 0P to 999P,Hold function: Possible to display both peak and bottom hold values, Selectable from 5 variationsBar LED monitor: Excess gain displayed (85% to 115% in 7 steps), Scaling displaySize30.3 mm (H) x 9.8 mm (W) x 71.8 mm (D) 1.19" (H) x 0.39" (W) x 2.83" (D)Detection modeLight intensity (area detection possible, automatic sensitivity-tracking function provided)/[Limited light intensity/Count check/Abnormality detection]Timer functionOFF-delay timer/ON-delay timer/One-shot timer/ON-delay timer + OFF-delay timer/ON-delay timer + One-shot timer, selectableTimer duration selectable: 0.1 ms to 9,999 ms, Maximum error against the setting value: ±10% max.Control outputPNP open-collector 24 V, 100 mA max.*1 (main unit only)/20 mA max. (when the expansion unit(s) is connected), Residual voltage: 1 V max.External inputyInput time: 2 ms (ON)/20 ms (OFF) min.*2Unit expansionUp to 16 expansion units can be connected (a total of 17 units). Note that the 2-output type should be counted as two units.Number of interference prevention unitsNormal operationHIGHSPEED：0 FINE：4 TURBO/SUPER/ULTRA/MEGA：8台RatingPower voltage12 to 24 VDC ±10 %, Ripple (P-P) 10 % or lessPower consumptionNormal: 830 mW max. (Using 24 V, 35 mA max., using 12 V, 45 mA max.)/Power saving 660 mW max. (Using 24 V, 27 mA max., using 12 V,32 mA max.)*3Environmental resistanceAmbient lightIncandescent lamp: 20,000 lux max., Sunlight: 30,000 lux max.Ambient temperature-10 to +55 °C 14 to 131 °F (No freezing)*4Relative humidity35 to 85 % RH (No condensation)Vibration resistance10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directionsShock resistance500 m/s2, 3 times in each of the X, Y, and Z directionsCase materialPolycarbonateAccessoriesN/AWeightApprox. 22 g*1 Total current of two outputs should be less than 100 mA.*2 Only available on certain models.*3 When using the HIGH SPEED mode, the power consumption increases by 160 mW (7 mA).*4 If more than one unit is used together, the ambient temperature varies with the conditions below. Mount the units on the DIN rail with mounting brackets and check that the output current is 20 mA or less.1 to 2 Units: -10 to +55 °C 14 to 131 °F, 3 to 10 Units: -10 to +50 °C 14 to 122 °F, 11 to 16 Units: -10 to +45 °C 14 to 113 °F